ASM Skimmer Club!

[RotaryGeek]

So of the two hydrofoamers, which one should i get? 9410.040 or the 9420.040?

 

[mc-cro]

I put the 9420 on my G4, and I have the airflow at about 50% If you have anything smaller then a G4, I would suggest the smaller pump.

 

[RotaryGeek]

ok, i think i already know the answer, but i have a Mag 12 laying around. Would that be a better pump than the sedra 9000?

 

[mc-cro]

fwiw, I use my mag 12 to mix AND HEAT my 30g water change container. seriously, it will bring my water temp up from about 72 to 80 in less than 6hrs. I wouldnt use it, plus you would have to figure out a needle wheel or mesh mod for it.

 

[RotaryGeek]

Yeah thats actually exactly what i use the mag for lol. Just a thought though.

 

[Anemonebuff]

I use the small one on my G3. The bubbles go about 1.5" below the uniseal. I have the air open full blast.

 

[cherubfish pair]

sirreal63,

I forgot if your recirc pump is Tunze or not. I was wondering how the Tunze would work in recirc fashion. Mostly about how the input tube would match up with a uniseal.

 

[mc-cro]

I was going to try the tunze in recirc position, but it was a challenge to get it plumbed in.

I found that with the tunze as the main pump, I got better results without the recirc sedra. and just used the tunze by itself and patched up the holes that were for the recirc.

 

[sirreal63]

I am still using the Sedra. I have tried numerous pumps over the year and nothing has worked better. I am not a fan of the Sedra, but it is hard to disagree with the results I get from it. I have a box full of pumps.

 

[davidwillis]

I just did a few more mods to my g-1. I moved the pump to below the skimmer, and set it up to recirculate. I also did the porting mod to the pump. I put in a plate to work as a bubble plate, but it didn't seem to work, so I took it out. Also, I tried running my return line from my tank to run cc in this, but it was too much flow (it pushed a lot of bubbles right out of the skimmer., so for now I am not using the recirculate, and am just feeding my return water into my pump. It still seems to have a lot of turbulence.

Here is a picture.

and here is a video
http://www.youtube.com/watch?v=SR0R0PfxtNI

 

[cherubfish pair]

^^Is that a Sedra pump? And which one?

 

[davidwillis]

^^Is that a Sedra pump? And which one?

lol.... I wish I knew. It looks like a Sedra, but I don't know. I bought it used, and there is nothing to indicate what it is.

 

[Dieselfool]

:reading::reading:

 

[Twiegs]

Does anyone know where I can find instructions on how to do the recirculation mod? What size holes to drill, what tool to use to drill the holes, etc...?

Thanks!

 

[Anemonebuff]

sirreal63,

I forgot if your recirc pump is Tunze or not. I was wondering how the Tunze would work in recirc fashion. Mostly about how the input tube would match up with a uniseal.

You will need to Mod the connections. However, the Tunze works best when submerged below the water line.

 

[cherubfish pair]

Does anyone know where I can find instructions on how to do the recirculation mod? What size holes to drill, what tool to use to drill the holes, etc...?

Thanks!

Depends on what pump you're using.

 

[Psirex]

Can someone verify the dimensions of the ASM G2 and the G3 everywhere I read it says 24 and 25 inches tall - which is too tall to fit under my stand...

 

[cherubfish pair]

Here's a table with specs:
http://www.championlighting.com/product.php?productid=32015&cat=1502&page=1

You might have to build a new stand. There's an excellent thread on building stands in the diy forum.

 

[Psirex]

Here's a table with specs:
http://www.championlighting.com/product.php?productid=32015&cat=1502&page=1

You might have to build a new stand. There's an excellent thread on building stands in the diy forum.

Ok, so there is no way the G2 or G3 less than 24 inches tall

 

[sirreal63]

My G3 is 24" tall.